A fully automatic solution for 60 to 600m³ applications.

Effective formulation against viruses, fungi and bacteria.

Sanitizes for up to 8 months*: The hot vaporization allows to spread in the environment invisible micro-particles that eradicate bacteria and viruses present on every surface and in fissure, ensuring sanitization even up to 8 months, in complete autonomy.

*low intensity sanitization – once a week – environment of 100m³ – tank 25 Liters.

Automatic system of sanitization: Once installed and connected to the main power, SANY SAFE is ready to use and does not require any technical assistance.

Tank replacement in autonomy: The external tank has been designed to be replaced directly by the user, without technical assistance. It is available in different sizes: 5, 10 or 25 liters to perform many sanitization cycles, according to your needs.

Management and monitoring by APP: Once installed, SANY SAFE has a programmed weekly schedule, that allows an immediate use. Thanks to the simple and intuitive configuration by APP, you can, at any time, manage SANY SAFE and customize volumes, frequency and intensity of the sanitization cycles.

Quick sanitization: 3 levels of intensity to choose the level and frequency of sanitization best suited to your environment. For example, you can do a low intensity sanitization every day in a 120m3room in a minute and enter after a quarter of an hour.

Connected to the Cloud: Thanks to the included GSM device and the DATA SIM active for 2 years*, SANY SAFE is always connected to the Cloud and can be controlled remotely. (Available only for European countries.)

Maximum security: The vaporized steam in the air does not present any toxicity to people, animals and plants, does not damage surfaces and tissues and releases a pleasant clean scent. The environment should be adequately ventilated after use.

Energy saving: SANY SAFE has been designed to dynamically manage consumption. During the time slots when the steam diffusion is not performed, SANY SAFE activates the standby mode, turning off and saving energy.

The post SANY SAFE: Environmental sanitization system appeared first on Bunker Seguridad Electrónica S.L..

No Toxic

No Odour

No Waste

The post FOGGY 50W – Anti-robbery Fog Generator appeared first on Bunker Seguridad Electrónica S.L..

BM is composed of 2 units – 1 transmitter (TX) and 1 receiver (RX) – installed at a maximum distance of 200 meters.

BMs integrate planar antennas which reduce of 20% the sensibility area compared to former parabolic antennas. Longer distances BM can be installed for the same perimeters and costs are saved. In addition, to be protected from rain, the parabolic antennas use big expansive difficult-to-handle waterproof housings when the BM’s planar antennas are highly protected by tropicalization and installed in high resistant protective cover that avoid the condensation and its consecutive rust development.

These microwave barriers operate in all weather conditions (snow, rain, fog) without distances reduction, unlike the active infrared barriers. If the temperature reaches less than -5°C, it is possible to place a TERM1 heating kit. BM temperature range is -20/+55°C.

Features:

• HIGHER SECURITY: The security area is genuinely so width and high (up to 4 x 3 meters) that it is impossible to cross without generating an alarm and provides a higher security compared to other technologies.
• LOWER FALSE ALARM RATE: Setting a pet immunity is easy: the alarm level is programmed to ignore small animals and generate less unwanted alarms.
• INTEGRATION CIRCUIT: The security may be increased automatically thanks to its build-in integration circuit which amplifies the possible conditions for an alarm and triggers more easily
• DISQUALIFICATION: BM distinguish a real alarm from a disqualification situation (like a van parked between the barriers).
• COMMON INTERFACE AND INSTALLATION: With the poles, BM are only 120 cm high: it is easy and quick to install them, so the cost of installation is lower compared to other technologies. It is also simple to set perfectly thanks to few trimmers and dip-switches. Finally, thanks to its regular NC outputs, BM works with all alarm and CCTV systems.

The post Analogue Microwave Barriers BM 200 M appeared first on Bunker Seguridad Electrónica S.L..

BM is composed of 2 units – 1 transmitter (TX) and 1 receiver (RX) – installed at a maximum distance of 120 meters.

BMs integrate planar antennas which reduce of 20% the sensibility area compared to former parabolic antennas. Longer distances BM can be installed for the same perimeters and costs are saved. In addition, to be protected from rain, the parabolic antennas use big expansive difficult-to-handle waterproof housings when the BM’s planar antennas are highly protected by tropicalization and installed in high resistant protective cover that avoid the condensation and its consecutive rust development.

These microwave barriers operate in all weather conditions (snow, rain, fog) without distances reduction, unlike the active infrared barriers. If the temperature reaches less than -5°C, it is possible to place a TERM1 heating kit. BM temperature range is -20/+55°C.

Features:

• HIGHER SECURITY: The security area is genuinely so width and high (up to 4 x 3 meters) that it is impossible to cross without generating an alarm and provides a higher security compared to other technologies.
• LOWER FALSE ALARM RATE: Setting a pet immunity is easy: the alarm level is programmed to ignore small animals and generate less unwanted alarms.
• INTEGRATION CIRCUIT: The security may be increased automatically thanks to its build-in integration circuit which amplifies the possible conditions for an alarm and triggers more easily
• DISQUALIFICATION: BM distinguish a real alarm from a disqualification situation (like a van parked between the barriers).
• COMMON INTERFACE AND INSTALLATION: With the poles, BM are only 120 cm high: it is easy and quick to install them, so the cost of installation is lower compared to other technologies. It is also simple to set perfectly thanks to few trimmers and dip-switches. Finally, thanks to its regular NC outputs, BM works with all alarm and CCTV systems.

The post Analogue Microwave Barriers BM 120 M appeared first on Bunker Seguridad Electrónica S.L..

BM is composed of 2 units – 1 transmitter (TX) and 1 receiver (RX) – installed at a maximum distance of 60 meters.

BMs integrate planar antennas which reduce of 20% the sensibility area compared to former parabolic antennas. Longer distances BM can be installed for the same perimeters and costs are saved. In addition, to be protected from rain, the parabolic antennas use big expansive difficult-to-handle waterproof housings when the BM’s planar antennas are highly protected by tropicalization and installed in high resistant protective cover that avoid the condensation and its consecutive rust development.

These microwave barriers operate in all weather conditions (snow, rain, fog) without distances reduction, unlike the active infrared barriers. If the temperature reaches less than -5°C, it is possible to place a TERM1 heating kit. BM temperature range is -20/+55°C.

Features:

• HIGHER SECURITY: The security area is genuinely so width and high (up to 4 x 3 meters) that it is impossible to cross without generating an alarm and provides a higher security compared to other technologies.
• LOWER FALSE ALARM RATE: Setting a pet immunity is easy: the alarm level is programmed to ignore small animals and generate less unwanted alarms.
• INTEGRATION CIRCUIT: The security may be increased automatically thanks to its build-in integration circuit which amplifies the possible conditions for an alarm and triggers more easily
• DISQUALIFICATION: BM distinguish a real alarm from a disqualification situation (like a van parked between the barriers).
• COMMON INTERFACE AND INSTALLATION: With the poles, BM are only 120 cm high: it is easy and quick to install them, so the cost of installation is lower compared to other technologies. It is also simple to set perfectly thanks to few trimmers and dip-switches. Finally, thanks to its regular NC outputs, BM works with all alarm and CCTV systems.

The post Analogue Microwave Barriers BM 60 M appeared first on Bunker Seguridad Electrónica S.L..

BM is composed of 2 units – 1 transmitter (TX) and 1 receiver (RX) – installed at a maximum distance of 200 meters. The transmitter continuously emits microwaves to the receiver. When an intruder passes between the two units, the received signal is reduced consecutively and on reaching the alarm level the alarm is generated. In addition, these barriers allow to detect and signal an accidental and permanent interruption of the beam.

BMs integrate planar antennas which reduce of 20% the sensibility area compared to former parabolic antennas. Longer distances BM can be installed for the same perimeters and costs are saved. In addition, to be protected from rain, the parabolic antennas use big expansive difficult-to-handle waterproof housings when the BM’s planar antennas are highly protected by tropicalizing resins and installed in high resistant protective cover that avoid the condensation and its consecutive rust development.

These microwave barriers are placed in containers specially designed to tolerate and facilitate even the most deilicate installations. They operate in all weather conditions (snow, rain, fog) without distances reduction, unlike the active infrared barriers. If the temperature reaches less than -5°C, it is possible to place a TERM1 heating kit. BM temperature range is -20/+55°C.

Features:

• AUTOMATIC GAIN CONTROL (AGC): The environmental variations may improve or deteriorate the microwaves level reception over time. An Automatic Gain Control circuit automatically optimizes the level to maintain it flat: the settings are easier, the security is higher.
• REDUCTION OF THE SENSIBILITY AREA: BM HP may reduce digitally of up to 30% the area of sensibility and then ignore the movements in the peripheral objects (i.e. from fences or trees) which are the origin of unwanted alarms.
• FALSE ALARM FILTER: BM HP barriers records automatically up to 3600 events it is possible to classify between good and false alarms. BM HP verifies then the new events according to this database and stop the unwanted alarms.
• DIGITAL INTERFACE: Additionally to the NC outputs and other regular settings, BM HP present a USB and a RS485 port to be coupled to a RS485 hub or an AVS ELECTRONICS’ control panel.
• SOFTWARE: Thanks to the local USB port or remotely by PSTN, GSM or IP, HPWIN software shows all the parameters, an oscilloscope, the 3600 last alarm events (with date and time) and proposes all the tools to set the barriers.

The post Digital Microwave Barriers BM 200 HP VAC appeared first on Bunker Seguridad Electrónica S.L..

BM is composed of 2 units – 1 transmitter (TX) and 1 receiver (RX) – installed at a maximum distance of 120 meters. The transmitter emits continuously microwaves in direction of the receiver. When an intruder passes between the two units, the received signal is reduced consecutively and on reaching the alarm level the alarm is generated. In addition, these barriers allow to detect and signal an accidental and permanent interruption of the beam.

BMs integrate planar antennas which reduce of 20% the sensibility area compared to former parabolic antennas. Longer distances BM can be installed for the same perimeters and costs are saved. In addition, to be protected from rain, the parabolic antennas use big expansive difficult-to-handle waterproof housings when the BM’s planar antennas are highly protected by tropicalizing resins and installed in high resistant protective cover that avoid the condensation and its consecutive rust development.

These microwave barriers are placed in containers specially designed to tolerate and facilitate even the most deilicate installations. They operate in all weather conditions (snow, rain, fog) without distances reduction, unlike the active infrared barriers. If the temperature reaches less than -5°C, it is possible to place a TERM1 heating kit. BM temperature range is -20/+55°C.

Features:

• AUTOMATIC GAIN CONTROL (AGC): The environmental variations may improve or deteriorate the microwaves level reception over time. An Automatic Gain Control circuit automatically optimizes the level to maintain it flat: the settings are easier, the security is higher.
• REDUCTION OF THE SENSIBILITY AREA: BM HP may reduce digitally of up to 30% the area of sensibility and then ignore the movements in the peripheral objects (i.e. from fences or trees) which are the origin of unwanted alarms.
• FALSE ALARM FILTER: BM HP barriers records automatically up to 3600 events it is possible to classify between good and false alarms. BM HP verifies then the new events according to this database and stop the unwanted alarms.
• DIGITAL INTERFACE: Additionally to the NC outputs and other regular settings, BM HP present a USB and a RS485 port to be coupled to a RS485 hub or an AVS ELECTRONICS’ control panel.
• SOFTWARE: Thanks to the local USB port or remotely by PSTN, GSM or IP, HPWIN software shows all the parameters, an oscilloscope, the 3600 last alarm events (with date and time) and proposes all the tools to set the barriers.

The post Digital Microwave Barriers BM 120 HP VAC appeared first on Bunker Seguridad Electrónica S.L..

BM is composed of 2 units – 1 transmitter (TX) and 1 receiver (RX) – installed at a maximum distance of 60 meters. The transmitter emits continuously the microwave in direction of the receiver. The intruder who passes through the 2 units reduces consecutively the received signal, up to reach the alarm level and generate the alarm.

BMs integrate planar antennas which reduce of 20% the sensibility area compared to former parabolic antennas. Longer distances BM can be installed for the same perimeters and costs are saved. In addition, to be protected from rain, the parabolic antennas use big expansive difficult-to-handle waterproof housings when the BM’s planar antennas are highly protected by tropicalization and installed in high resistant protective cover that avoid the condensation and its consecutive rust development.

These microwave barriers operate in all weather conditions (snow, rain, fog) without distances reduction, unlike the active infrared barriers. If the temperature reaches less than -5°C, it is possible to place a TERM1 heating kit. BM temperature range is -20/+55°C.

Features:

• AUTOMATIC GAIN CONTROL (AGC): The environmental variations may improve or deteriorate the microwaves level reception over time. An Automatic Gain Control circuit automatically optimizes the level to maintain it flat: the settings are easier, the security is higher.
• REDUCTION OF THE SENSIBILITY AREA: BM HP may reduce digitally of up to 30% the area of sensibility and then ignore the movements in the peripheral objects (i.e. from fences or trees) which are the origin of unwanted alarms.
• FALSE ALARM FILTER: BM HP barriers records automatically up to 3600 events it is possible to classify between good and false alarms. BM HP verifies then the new events according to this database and stop the unwanted alarms.
• DIGITAL INTERFACE: Additionally to the NC outputs and other regular settings, BM HP present a USB and a RS485 port to be coupled to a RS485 hub or an AVS ELECTRONICS’ control panel.
• SOFTWARE: Thanks to the local USB port or remotely by PSTN, GSM or IP, HPWIN software shows all the parameters, an oscilloscope, the 3600 last alarm events (with date and time) and proposes all the tools to set the barriers.

The post Digital Microwave Barriers BM 60 HP VAC appeared first on Bunker Seguridad Electrónica S.L..

BM is composed of 2 units – 1 transmitter (TX) and 1 receiver (RX) – installed at a maximum distance of 200 meters. The transmitter continuously emits microwaves to the receiver. When an intruder passes between the two units, the received signal is reduced consecutively and on reaching the alarm level the alarm is generated. In addition, these barriers allow to detect and signal an accidental and permanent interruption of the beam.

BMs integrate planar antennas which reduce of 20% the sensibility area compared to former parabolic antennas. Longer distances BM can be installed for the same perimeters and costs are saved. In addition, to be protected from rain, the parabolic antennas use big expansive difficult-to-handle waterproof housings when the BM’s planar antennas are highly protected by tropicalizing resins and installed in high resistant protective cover that avoid the condensation and its consecutive rust development.

These microwave barriers are placed in containers specially designed to tolerate and facilitate even the most deilicate installations. They operate in all weather conditions (snow, rain, fog) without distances reduction, unlike the active infrared barriers. If the temperature reaches less than -5°C, it is possible to place a TERM1 heating kit. BM temperature range is -20/+55°C.

Features:

• AUTOMATIC GAIN CONTROL (AGC): The environmental variations may improve or deteriorate the microwaves level reception over time. An Automatic Gain Control circuit automatically optimizes the level to maintain it flat: the settings are easier, the security is higher.
• REDUCTION OF THE SENSIBILITY AREA: BM HP may reduce digitally of up to 30% the area of sensibility and then ignore the movements in the peripheral objects (i.e. from fences or trees) which are the origin of unwanted alarms.
• FALSE ALARM FILTER: BM HP barriers records automatically up to 3600 events it is possible to classify between good and false alarms. BM HP verifies then the new events according to this database and stop the unwanted alarms.
• DIGITAL INTERFACE: Additionally to the NC outputs and other regular settings, BM HP present a USB and a RS485 port to be coupled to a RS485 hub or an AVS ELECTRONICS’ control panel.
• SOFTWARE: Thanks to the local USB port or remotely by PSTN, GSM or IP, HPWIN software shows all the parameters, an oscilloscope, the 3600 last alarm events (with date and time) and proposes all the tools to set the barriers.

The post Digital Microwave Barriers BM 200 HP appeared first on Bunker Seguridad Electrónica S.L..

BM is composed of 2 units – 1 transmitter (TX) and 1 receiver (RX) – installed at a maximum distance of 120 meters. The transmitter continuously emits microwaves to the receiver. When an intruder passes between the two units, the received signal is reduced consecutively and on reaching the alarm level the alarm is generated. In addition, these barriers allow to detect and signal an accidental and permanent interruption of the beam.

BMs integrate planar antennas which reduce of 20% the sensibility area compared to former parabolic antennas. Longer distances BM can be installed for the same perimeters and costs are saved. In addition, to be protected from rain, the parabolic antennas use big expansive difficult-to-handle waterproof housings when the BM’s planar antennas are highly protected by tropicalizing resins and installed in high resistant protective cover that avoid the condensation and its consecutive rust development.

These microwave barriers are placed in containers specially designed to tolerate and facilitate even the most deilicate installations. They operate in all weather conditions (snow, rain, fog) without distances reduction, unlike the active infrared barriers. If the temperature reaches less than -5°C, it is possible to place a TERM1 heating kit. BM temperature range is -20/+55°C.

Features:

• AUTOMATIC GAIN CONTROL (AGC): The environmental variations may improve or deteriorate the microwaves level reception over time. An Automatic Gain Control circuit automatically optimizes the level to maintain it flat: the settings are easier, the security is higher.
• REDUCTION OF THE SENSIBILITY AREA: BM HP may reduce digitally of up to 30% the area of sensibility and then ignore the movements in the peripheral objects (i.e. from fences or trees) which are the origin of unwanted alarms.
• FALSE ALARM FILTER: BM HP barriers records automatically up to 3600 events it is possible to classify between good and false alarms. BM HP verifies then the new events according to this database and stop the unwanted alarms.
• DIGITAL INTERFACE: Additionally to the NC outputs and other regular settings, BM HP present a USB and a RS485 port to be coupled to a RS485 hub or an AVS ELECTRONICS’ control panel.
• SOFTWARE: Thanks to the local USB port or remotely by PSTN, GSM or IP, HPWIN software shows all the parameters, an oscilloscope, the 3600 last alarm events (with date and time) and proposes all the tools to set the barriers.

The post Digital Microwave Barriers BM 120 HP appeared first on Bunker Seguridad Electrónica S.L..